The convenience electronics central control unit J393 is also located in the luggage compartment on the right. The effect of this is described on the previous page. Last week it was down at 9mpg. They must not be rotated by more than 30° relative to one another. Gate valve 38 Locking lever Selector lever gate Suspension system Overview Four alternative suspension systems are used on the Audi A4 '08. A pyrotechnic battery disconnect device is used.
The damping control system comprises the third group. Seat air conditioning is requested by the climatronic control unit J255 on the basis of its settings. The heating and ventilation settings can be selected via the two rotary temperature controls on the climatronic control unit J255. The microswitch is actuated when the Eurostandard plug is inserted. Due to the new body design, however, several components have been adapted to meet the new requirements. Using the information provided by the seat position sensors, the airbag control unit J234 determines whether the driver and front passenger seats in at the front or back of the seat adjustment range. In such a case, the gearshift mechanism must be replaced.
For information about maintenance and repair work, always refer to the current technical literature. This avoid warnings being issued constantly when driving in parallel with a lane marking. If the seat ventilation system is activated at high interior temperatures, there is a short delay until a comfortable seat climate is achieved because, due to the operating principle of the system, heated air is initially drawn in from the footwell area until the air conditioning system has cooled down the occupant cell. B - Modified flange shafts are used on the gearbox and on the final drive. They can be distinguished at first glance by their different air conditioning control units. The auxiliary water pump for exhaust gas recirculation starts up when the exhaust gas recirculation is active and the bypass valve is closed.
The seal and the shoulder on the flange shaft can also be clearly recognised. A - In addition to sealing, the rubberised metal seal has the task of providing a frictional connection. Si tratta di parti della pagina visitata generate direttamente dai suddetti siti ed integrati nella pagina del sito ospitante. The rebound and compression damping adjustment range lies between the red limiting characteristics. To activate the system, the lane departure warning system button in the indicator lever must be operated. Note, it is believed that you also have to replace the other shock on the failed circuit, but I have not found any Audi tech info to confirm this. Both adjustment ranges are available for the driver and the front passenger.
That is why it does not begin to operate until the vehicle is travelling a speed of approx. The high-pressure pump is supplied with fuel with a pressure of approx. In case of failure of the sensor, the automatic air recycle function will be unavailable. Until then the central valve has to be replaced if it loses pressure. The front and rear axle components have been carried over from the Audi A5, except for the springs, shock absorbers and anti-roll bars. The equally all-new S line competition equipment line provides additional dynamic highlights.
Suspension systems fitted with conventional damping components have a fixed damping force to damping rate ratio. Audi has experienced great success with its sporty S models over a period of twenty years. Loose terminal at alternator connection is the latest stated cause. The hole pattern of the prop shaft joint and the axle flange must be joined together in such a way that the coloured marks align. The relative humidity and temperature at the windscreen are measured using a capacitive thin film sensor. By connecting diagonally opposed shock absorbers vehicle pitching and diagonal chassis movements are minimised. Again, gear selector position P switch F305 provides the information for enabling the ignition key.
Follow the instructions given in the Workshop Manual. Think I have learnt my lesson again. I'm gonna wait to see how the vat rise affects my income and then take it from there. A servotronic function is optionally available. Emergency release Solenoid N110 can be actuated with an aid e.
A targeted pressure pulse from igniter 2 causes rupture disc 2 to burst. Consentono, per esempio, di rilevare se il medesimo utente torna a collegarsi in momenti diversi. The 2019 model year will see the A4 Sedan and A4 Avant receive newly designed bumpers, which together with the new wheel design accentuate the sporty character. To activate the change of setting for the engine, too, the accelerator pedal must be briefly depressed. If F305 is faulty, it can, as mentioned already, easily be replaced. Prop shaft with new sealing and assembly concept refer to page 30 ff.