Toward the tail of the concert I'd begun to get tired. The Modified Life staff has taken all its Nissan Versa headlight bulb replacement guide, 2012 Nissan Versa replace light bulb size guides, Nissan Versa light bulb replacement guides and cataloged them online for use by our visitors for free. I refer to your work. Identify where the retainer studs and sliding clips are on the tail light before removing it. Turn the tail light assembly down on to the bumper. If they don't have vanilla, how about chocolate? Some of the other bulbs in the tail light cluster such as the brake light or turn signal may also function as the tail light in your Versa. Yes it is a pia to replace the tail lights in a 2011 versa ,sedan! Nissan Tilda outside North America is fairly simple, here's the guide to do it your self.
If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. It seems like just replacing the taillight could damage those. Disconnect the connectors from the taillights taillight bulb connectors are visible by looking inside the trunk at the back of the tail lamps. You also also download more pictures by clicking the photo below or read more at this article:. Please help support this website by shopping at. The black plastic brake light bulb socket is located closest to the outside edge of the vehicle. Note: I am not a registered charity.
Once both of the 10mm nuts have been removed, you can gently pull off the tail light assembly from the rear corner of the vehicle. Remove the nuts and screws, then remove the taillight. In some cases, the order may ship the next business day. To create this article, volunteer authors worked to edit and improve it over time. Test the new bulbs by turning on the headlights, activating the hazard lights and flashing the high beams.
For more, check out my other. When you replace the brake light bulb on your Versa, be careful not to touch the bulb directly with your fingers - the oil from your skin will cause the area that you touched to burn hotter than the rest of the bulb, which causes the bulb to burn out quicker. Use of the 2012 Nissan Versa replacement bulb size information is at your own risk. I guess that doesn't sound so bad but it doesn't slide out that easy or slides back in. In addition to the little share you can also produce sebuaha little waterfall or a modest feature that is employed with organic aspects, such as the usage of timber being a water flushed or by the utilization of stones, where the water is going to be proven more obviously too.
Once I got the stud lined up with the catch, I had to gently press on the points of the triangle at the bottom rear and top side to slip the catch into place on the stud. Donations are not tax deductible. We have worked hard to design a site that caters to everyones Nissan Versa Tail Light needs. It is possible for the turn signal or brake light to work but the tailight part to be burnt out - replacing the bulb on your Versa will restore functionality to both. The housing on my lights is more of a triangle, with sharp points at the bottom rear and top side of the car, and the stud catch in the center of the triangle at the third point at the bottom side of car.
Hold the tail light with one hand while spinning on the two 10mm nuts. I couldn't have done it without them! Brake light bulbs grow dimmer over time and eventually burn out. Tighten the nuts with the socket and ratcheting wrench. There may be an interior trunk trim panel that you have to take off but in most cases its just a series of thumb screws that hold them in. Once both nuts are removed, proceed to the outside of the taillight assembly and gently insert a flat head screwdriver between the taillight and vehicles body, starting at the bottom of the Taillight. Hello , this attachment is about Good How To Replace A Tail Light 2 Nissan-Versa-Hatchback-Tail-Light-Bulbs-Replacement-Guide-012.
To avoid scratching the bumper or tail light, place a towel between them. The first few steps are to open the cargo area tailgate, move to the side of the vehicle with the burnt out tail light bulbs and locate the two rectangular plastic access panels. Some of the other bulbs in the tail light cluster such as the brake light or turn signal may also function as the tail light in your Versa. These are the best instructions I've found for replacing the Nissan Versa sedan tail light. We love when auto parts experts come to our site and we love when car parts newbies come to our site. Use a pair of needle nose pliers and get the light out.
Also, for good and all. Please help support this website by shopping at. Check your bulbs frequently and change burnt bulbs promptly. I never was able to get the wire harness off. If You ought to download It to Your computer, you could. The brake lights on your 2008 Nissan Versa illuminate when you hit the brake pedal and help prevent you from being rear ended by the cars behind you.
There are either 3 or 4 nuts holding the tail-light assembly in place, which means youll need to take out most of the inner panels to access the others. This small yard indicates a natural area that is about the front of the house being a tiny spot with various kinds of flowers which are beautiful and able to identify a beautiful green location. Once both of the 10mm nuts have been removed, you can gently pull off the tail light assembly from the rear corner of the vehicle. Carefully push the tail light on to the rear of the vehicle. Then remove the black rubber dust boot that surrounds the headlight bulb and set it aside in a safe place.
Identify where the retainer studs and sliding clips are on the tail light before removing it. Backed by 1-year, unlimited-mileage warranty -- Replacement brand parts are the most affordable solution for your replacement needs! Entering your vehicle information in our Year Make Model selector up top, helps ensure you get an auto part that fits your car, truck or other type of vehicle. Here's a quick guide to changing the Taillight bulb on a 2006-2013 Nissan Versa Hatchback. Be careful how you act. Most in-stock orders will ship out within 24 hours and will reach customers within approximately a week. It came in excellent condition. The headlight bulb is held in place by a two prong metal retaining arm.