Step 1 all bolts tighten to 18 ft,lbs no diagram, start in the middle and work your way out going cris cross. I broke my composite cover when I backed into a rock, the billet aluminum ones will do the same thing although not as easily. Go to the front of the vehicle and release the auxiliary latch that is located on the front bumper under the grill. Vehicle Curb Weight — is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Failure to drive cautiously could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death. Rotate the panels toward the tailgate.
Because of the steps involved, it may be helpful to have another person assist you in programming the transmitter. Ford does not recommend disabling this feature except in situations where speed reduction may be detrimental e. Changes to towing conditions include trailer load, vehicle load, road conditions and weather. Your vehicle is not equipped with the Ford Ambulance Preparation Package. These ratings are listed in the following chart. A certain pressure -- or preload -- on the pinion bearing and spacer must be established.
This program is separate from the New Vehicle Limited Warranty. Selectable languages are English, Spanish, or French. Check the sidewalls to make sure there are no gouges, cuts or bulges. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues. Try to pull the belt out of the retractor to make sure the retractor is in the automatic locking mode you should not be able to pull more belt out.
Make sure the headlamp control is in the off position. Refer to Safety restraints for children or Safety seats for children later in this chapter. Both my vehicles had 100,000 Kms on them 60,000 miles when I changed them to synthetic. Anybody know the actual torque value, is the number in the Chilton manual just an uncorrected mistake? Disconnect the electrical connector from the fog lamp bulb. The third member fits in a banjo-type axle housing that does not have a rear cover. The suspension provides about an inch of lift too. A correct zone setting will eliminate this error.
Use only Ford recommended replacement fasteners. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Lift tailgate to a 80-degree angle from horizontal. If the minimum torque needed to rotate the pinion nut is not established by the minimum nut torque, the nut must be tightened further, in small increments, until the proper torque value is established. Vehicles equipped with traditional keys: When using a Ford-approved remote start system, the default settings will recognize the remote start system as an additional Admin Key with its associated privileges. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
This added width gave engineers the platform to increase wheel travel. I too replaced my composite cover with a metal Ford one. Push seat cushion down until it locks into horizontal position. Slip the air tube onto the air filter housing and tighten the air-tube clamp bolt snugly, but do not overtighten it. Power steering fluid reservoir 7. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield.
Note that these measurements are in inch-pounds and require an inch-pound torque wrench. Mar 23, 2012 Heres the diagram and specs for the cylinder head and also i have enclosed the torque specs for the intake and its tightening sequence, good luck and hope this is helpful, have a good day. Besides the dimensions you can also read detailed information concerning engine of the vehicle such as engine size, horsepower, the number of cylinders and valves, which can tell you a lot about potential performance of the car. Additional Car2U system information can be found on-line at www. To activate the heated mirrors, press the rear defrost button located on the climate control panel.
So how does this truck handle extreme off-road conditions? Speed control: Illuminates when the speed control is activated. Repeat steps 4 and 5 until you are done changing the optional settings. When installing cleat, reverse instructions above. If fuel is splashed in the eyes, remove contact lenses if worn , flush with water for 15 minutes and seek medical attention. If the authorized dealer employees cannot help you, they can direct you to the nearest Ford affiliate office.