On a downgrade, do not coast with the clutch pedal depressed or the transmission in neutral. Please keep this manual in the vehicle at all times. Insert the wire through the hole in the Push the contact out from the horn steering wheel where the old contact button area. This applies to the vehicle models without fairings. The light in the button comes on when the button is pressed for air recirculation. The cabinet 12 V outlets are made for 12 V accessory-type plugs.
The brakes used as one. Place the seat cushions toward the walls and then position the backrest cushions as illustrated. When the engine has started, it takes a while to send lubricating oil to all bearings and shafts, and between pistons and liners. Damage to the fifth wheel, trailer kingpin and slider may occur if not operated properly and may lead to an accident, causing serious personal. Be especially cautious of low-lying or closed-in areas. If exhaust smoke is visible during engine operation, this indicates a problem with the exhaust aftertreatment system. W3001007 1 Spacers Remove 3 bolts from the fuse panel,.
Check to see that the trailer is at the proper height for coupling. Loose wheel bearings could cause premature tire wear and possibly affect vehicle handling. In this case, brake control remains in the foot brake valve. Volvo D13 375-500 hp 1450-1850 lb-ft. Primary system components requiring noise related inspection include the hood, engine compartment insulating materials including hood insulation, bulkhead insulation, doghouse insulation, etc.
Spring Eye and Hanger Lift Method This method is permitted for under lift equipped units. To read more about the cookies, see our. Got told its on the back of the gear box on the rhs black lid with 4 screws and a plug?? Even if the vehicle can be driven after a collision, it is not recommended to drive the truck with the airbag deployed. It provides precise temperature control to the sleeper unit. The pressure generated by the intake manifold pressure should be the same at a given engine temperature, speed and load.
This can be hooked up to the multiplex box. The axle model and serial number is located on the front left side of the forward drive axle and the front right side of the rear drive axle. End gates free from damage, properly secured in stake pockets. Put the left foot fully on the bottom step and pull yourself up to the opening. Permanent lockout prevents performing a parked Regeneration when a condition exists that requires vehicle service. The switch has a safety latch to prevent accidental engagement. Axles An axle out of alignment increases rolling resistance.
There are two methods for opening the hood. When trailer air and electrical connections can not be coupled from the ground, Federal Regulations require commercial carriers to provide back-of-cab access steps, grab handles and plates. W5001433 Chock the trailer wheels. . Volvo D13 375-500 hp 1450-1850 lb-ft. Seat Adjustments W8002744 National Comfort Seat 1.
Transfer the body weight by leaning away from the hood. Variations in engine load can cause the exhaust temperature to vary. Whenever equipment requires adjustment, replacement, repair or lubrication, refer to the Service Manuals or contact an authorized Volvo Truck dealer for the correct procedures, specifications and intervals. Stand at the rear fender edge on the driver side of the vehicle. Make sure the belts are not twisted. W9000237 A direct visual check is required to ensure proper coupling. Follow the instructions below to avoid damage.
When the system is ready to be checked, the following screen displays. Lock the trailer brakes by pulling out the Trailer Supply knob. Each antenna carries multiple wire windings that work together with mirror bracket devices to cover the needs of many uses. Check the buckle and latch casing for cracks or breakage. Standard equipment is a normal ignition switch.
Note: There is a release latch behind the seat. There are several variants of instruments, depending on what options have been The graphic display is in the lower left-hand side of the installed on the vehicle, and on whether the speedometer instrument cluster. Beacon Lamps Switch W3005428 Sleeper Fan Speed Switch. W3005282 The red stud is the positive terminal and the black stud is the ground terminal. Irrespective of how the air distribution is set, a small amount of air will always come from the dashboard vents to ensure the temperature in the cab is correct. Please be aware that if you change your cookie settings, we are no longer able to ensure our website to function properly. Also, read the literature provided by the manufacturer.
When changing gears, avoid lugging to extend engine life. Remove the 2 clips at the bottom of the steering column cover. The air exhausts from the park brake valve itself and from the spring brake chambers on the rear axle s. Press the top part of the switch to raise the axle and press the lower part of the switch to lower the axle. There is no alarm in this unit. These starting and operating procedures should be followed for all engines. Rain, snow, icy conditions and headwinds have a large negative impact on fuel economy, as do hilly roads and uneven road surfaces.