You can even purchase your Tiburon headlight online and enjoy home shipping or take advantage of our Same Day Store Pickup option if you need your replacement immediately. Please check your local laws if you have any concerns regarding legality. There was very little clouding of the lens when I finished and 7 hours after I installed them they are almost clear. Please be aware that it is illegal in some areas to have tinted headlight covers, even if they are in use during the day. A few applications with a 3, 4, or 5 level difficulty will require some acquired knowledge and mechanical ability in which we cannot be held accountable.
They can be cheap insurance against having to replace expensive factory or aftermarket Hyundai Tiburon headlights, and best of all they look great whether you're at a show or cruising down the road. These bulbs have a very high voltage that runs through them, even if the battery is disconnected. You are responsible to make prior arrangement with the carrier if you are not available to receive and sign for the product. How long will it take to get my Lamin-x? There are also adhesive Hyundai Tiburon headlight covers that cling to your headlights, offering invisible protection from the elements. Once the excess is properly spread about the perimeter of the LampGard, the material will easily lay flat on the lens.
LampGard Headlight Protection offers exceptional protection for your headlamps. Changing both headlight bulbs on your Tiburon at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. This is completely normal and is no cause for concern. Once installed, I was concerned about all of the moisture trapped under the material. It's better to show us the picture of the part you need or tell us the part number.
I highly recommend this product. We are very satisfied with the results and will be purchasing this product for our other car. Don't need to replace the whole headlight assembly, you only need to repair your plastic headlight lens cover, it means only need to replace the lenses cover and then your headlights can back to condition as new. When working toward the edge, spread the excess material out rather than working it all into one spot. The LampGard also helps prevent scratches, pitting and staining from road debris.
I was able to remove almost all the air bubbles with my fingers then used the squeegee to remove the soapy solution. A: Headlight covers are attached to your existing headlight using double-sided tape. I have already been through the car wash several times without incident. Lamin-x is not responsible if the product is verified as delivered with the carrier to the specified address, but you personally did not receive it. Since I had already received the covers, I decided to go ahead and install them despite the hazy lens.
Headlight covers have been one of the mainstays of automotive customizing for decades, and are generally available in clear, smoked, and black, as well as with a carbon fiber look. My car had four pieces running lights and headlamps and all were precision-cut to fit like a glove. While the film is warm, slowly peel the film from the lens surface. Although, very few and seemingly simple, I was immediately concered about being able to curve the protector over and around the headlight. I ordered these headlight covers for a Mazda I prepped for shipment to Alaska. Kelly Hudgens First, they were cut perfectly but they are thick - nothing like those screen protectors for phones, iPads, etc. It is important to read the instructions first before attempting to apply the product and to be carefully around the curves of your lamps.
How do I remove the film from my paint? Once the film fully cures, most imperfections will disappear completely. LampGard Headlight Protection offers exceptional protection for your headlamps. Its built-in ultraviolet inhibitors prevent the material from discoloring, and its self-healing technology delivers unsurpassed scratch resistance. On larger headlamp pieces, the wet installation method is recommended as bubbles and improper alignment of the material are far less likely. However, if you encounter a stubborn bubble, you can poke it with a sewing needle and push out the air or water. This note is just to say Thanks for supplying a good product! This note is just to say Thanks for supplying a good product! The independent rear setup and stabilizer bars front and back provide sharp, precise handling on curvy roads. These things softened right up with a little heat, they stuck and moulded right on to fit like a glove! One cleared up beautifully, but the other was still a little hazy no matter what i tried.
The film is very thick and hard to work with if you can't keep it heated. You are responsible to make prior arrangement with the carrier if you are not available to receive and sign for the product. Headlight covers are a great way to protect your Hyundai Tiburon headlights from unexpected damage, such as that from rocks or the occasional tumbleweed. We recommend that you seek professional assistance if you are continuing to have installation issues. Are these films legal in my state? Keep the material warm and continue making short squeegee strokes from the center outward, gradually working toward the edge of the lens. I am very pleased with these covers.
The hole will eventually close on its own. This is completely normal and is no cause for concern. I was delighted to find that somehow the covers made the light haze on the one troublesome lens disappear. About a week later, I was blown away about how crystal clear they have become. You will need a helper.
Hello, About a year ago I ordered the WeatherTech Lampguard kit for my 2001 Toyota Tacoma. I never heated the lens when applying. We are very satisfied with the results and will be purchasing this product for our other car. I installed these today by myself with no problem. Please let us know where are you come from We can check shipping cost to your place directly with this information. A Lamin-x custom cut kit for your Hyundai Tiburon 2007-2008 is designed to give your car a one-of-a-kind combination of style and protection on its headlights.