Refer to the procedure in this section. Remove the radio - two pairs of screws on each side of the radio hold it in place. This will relieve the tension on the belt. Removing stereo: Front side of and rear side means to the front direction or rear direction of the vehicle. Remove the screws from the front of the mounting brackets. There are at least two screws in the plastic door panels: a metal one in the latch assembly and a plastic one at the rear end of the door.
To decide if your belt needs replacing, simply look at the grooved side of the belt to see if it is cracking badly. Make sure to chock wheels and or lock the parking brake on. Unplug the antenna and th … e wiring harnesses. If it blow out again; it has a broken wire that touch ground. If that doesn't work then take a wide screw driver from the bottom up to the locations of the bottom clips, push firmly and pull out one bottom side at a time. Op you could probably get a replacement cassette deck at a scrap yard, although you would be much better off getting an after market stereo.
For this reason, standard vehicle equipment does not always match the latest media technology taking the world by storm. To access them, start by pulling off the 2 round knobs and the 2 small slide lever knobs, they just pull off. Remove cotter key, castle lock and nut at center of rotor that attaches the axle. Hi all, The center console on my verso doesn't seem to be fitted straight, which results in the compartment on top of the dash having a big gap on the left and no gap on the right. Thats the annoying thing about the 2000 - 2002 corolla's the stereo is embedded in the dash. The Modified Life staff has taken all its Toyota Corolla car alarm wiring diagrams, Toyota Corolla car security wiring diagrams, Toyota Corolla car alarm wire diagrams, Toyota Corolla car security wiring schematics, Toyota Corolla car security diagrams, Toyota Corolla remote starter wiring diagrams and cataloged them online for our visitors to use for free.
Pull out the crappy stereo. The drop down menu at the top will help you find a topic of interest or you can If you have any questions about the site, head over to the. Remove plastic shield from under vehicle on passenger side. I don't need a sub woofer as I got all the Q values right along with the cabinet volume. Tighten retaining screw to 3-4 Nm 25-35 lb-in. Use of the wiring information is at your own risk.
They sell a tool specifically for it at auto zone, or someplace like that for u … nder five dollars. Lift and Support the vehicle. Remove the factory installed radio the instructions apply only for Corollas from 95-98. Unplug the back up switch. You can also Private Message one of our Community Managers. It's a factory 'moulding' error. Grab the plastic bar between the heating vents and the stereo.
To pull the plastic baffle off the dashboard: Adjust the heating vents so they point downwards. Then you need to snap the faceplate off using a small screwdriver or similar to gently move it around the little catches on the edges, it comes off. I have the same problem with the left side higher than the right and am sure its a moulding problem. Connect the wires from the plug that came with the new radio to the wiring harness adapter that you purchased separately. For starters get yourself a service manual. Do the same for the other side. I am guessing that somebody previous owner or dealer has had the console out and not put it back properly.
If you try to attach these, tiny metal studs on the brackets will interfere with the attachment, so grind them down with a dremel tool or file. Test the radio one more time just to be sure. Owners with little or no experience can have to old stereo removed in less than one-half hour. The main source of entertainment for most drivers is their music. In some models, this is also the radio accessory wire. There is one under your hood on the driver's side and the other is under the dash just to the left of steering wheel. I Power Antenna Wire 2.
Once the steering column has been removed from the vehicle, be careful not to drop it especially on it's end , lean on it or damage it in any way; the column is very susceptible to damage. Never got around to fixing it though as he doesn't really use the radio. Fit the sub brackets L + R using screws as shown. I can attest to a sterling job my friend. Be very carefull not to force it to prevent breking the clips that hold these air vent strips. Then carefullu pull up on panel containing power door lock and window switches.
I used Monster Cable to get the sound to the speakers. If you are unsure how your radio comes out, you should consult a service manual for your specific model. Then insert blank tape and connect mp3 player to new 3. So, what are you waiting for? The location of these clips is just below the vents. Once that is off, you can easily see the 6 10mm bolts to remove the stereo, then the smaller phillips screws on the sides of the stereo to unbolt it from the mount.